*nix Documentation Project
·  Home
 +   man pages
·  Linux HOWTOs
·  FreeBSD Tips
·  *niX Forums

  man pages->NetBSD man pages -> ipsec_set_policy (3)              



NAME    [Toc]    [Back]

     ipsec_set_policy, ipsec_get_policylen, ipsec_dump_policy - manipulate
     IPsec policy specification structure from readable string

LIBRARY    [Toc]    [Back]

     IPsec Policy Control Library (libipsec, -lipsec)

SYNOPSIS    [Toc]    [Back]

     #include <netinet6/ipsec.h>

     char *
     ipsec_set_policy(char *policy, int len);

     ipsec_get_policylen(char *buf);

     char *
     ipsec_dump_policy(char *buf, char *delim);

DESCRIPTION    [Toc]    [Back]

     ipsec_set_policy() generates IPsec policy specification structure, namely
     struct sadb_x_policy and/or struct sadb_x_ipsecrequest from human-readable
 policy specification.  policy specification must be given as C
     string policy and length len of policy.  ipsec_set_policy() will return
     the buffer of IPsec policy specification structure.  The buffer is dynamically
 allocated, and must be freed by the caller by calling free(3).

     You may want the length of the generated buffer such when calling
     setsockopt(2).  ipsec_get_policylen() will return the length.

     ipsec_dump_policy() converts IPsec policy structure into readable form.
     Therefore, ipsec_dump_policy() can be regarded as inverse conversion of
     ipsec_set_policy().  buf points to a IPsec policy structure, struct
     sadb_x_policy.  delim is a delimiter string, which is usually a blank
     character.  If you set delim to NULL, single whitespace is assumed.
     ipsec_dump_policy() returns pointer to dynamically allocated string.  It
     is caller's responsibility to reclaim the region, by using free(3).

     policy is formatted as either of the following:

     direction discard
              direction must be in or out.  direction specifies which direction
 the policy needs to be applied.  With discard policy, packets
 will be dropped if they match the policy.

     direction entrust
              entrust means to consult to SPD defined by setkey(8).

     direction bypass
              bypass means to be bypassed the IPsec processing.  (packet will
              be transmitted in clear).  This is for privileged socket.

     direction ipsec request ...
              ipsec means that the matching packets are subject to IPsec processing.
  ipsec can be followed by one or more request string,
              which is formatted as below:

              protocol / mode / src - dst [/level]
                       protocol is either ah, esp or ipcomp.

                       mode is either transport or tunnel.

                       src and dst specifies IPsec endpoint.  src always means
                       ``sending node'' and dst always means ``receiving
                       node''.  Therefore, when direction is in, dst is this
                       node and src is the other node (peer).  If mode is
                       transport, Both src and dst can be omitted.

                       level must be set to one of the following: default,
                       use, require or unique.  default means that the kernel
                       should consult the system default policy defined by
                       sysctl(8), such as net.inet.ipsec.esp_trans_deflev.
                       See ipsec(4) regarding the system default.  use means
                       that a relevant SA can be used when available, since
                       the kernel may perform IPsec operation against packets
                       when possible.  In this case, packets can be transmitted
 in clear (when SA is not available), or encrypted
                       (when SA is available).  require means that a relevant
                       SA is required, since the kernel must perform IPsec
                       operation against packets.  unique is the same as
                       require, but adds the restriction that the SA for outbound
 traffic is used only for this policy.  You may
                       need the identifier in order to relate the policy and
                       the SA when you define the SA by manual keying.  You
                       can put the decimal number as the identifier after
                       unique like unique: number.  number must be between 1
                       and 32767 .  If the request string is kept unambiguous,
                       level and slash prior to level can be omitted.  However,
 it is encouraged to specify them explicitly to
                       avoid unintended behaviors.  If level is omitted, it
                       will be interpreted as default.

     Note that there is a bit difference of specification from setkey(8).  In
     specification by setkey(8), both entrust and bypass are not used.  Refer
     to setkey(8) for detail.

     Here are several examples (long lines are wrapped for readability):

           in discard
           out ipsec esp/transport//require
           in ipsec ah/transport//require
           out ipsec esp/tunnel/
           in ipsec ipcomp/transport//use

RETURN VALUES    [Toc]    [Back]

     ipsec_set_policy() returns a pointer to the allocated buffer of policy
     specification if successful; otherwise a NULL pointer is returned.
     ipsec_get_policylen() returns with positive value (meaning the buffer
     size) on success, and negative value on errors.  ipsec_dump_policy()
     returns a pointer to dynamically allocated region on success, and NULL on

SEE ALSO    [Toc]    [Back]

     ipsec_strerror(3), ipsec(4), setkey(8)

HISTORY    [Toc]    [Back]

     The functions first appeared in WIDE/KAME IPv6 protocol stack kit.

BSD                               May 5, 1998                              BSD
[ Back ]
 Similar pages
Name OS Title
ipsec_strerror FreeBSD error message for IPsec policy manipulation library
ipsec_strerror NetBSD error code for IPsec policy manipulation library
setkey FreeBSD manually manipulate the IPsec SA/SP database
ipsec_mgr Tru64 Manipulate the state of the IPsec subsystem
XmConvertStringToUnits HP-UX A function that converts a string specification to a unit value
XmStringFreeContext HP-UX A compound string function that releases the string scanning context data structure
getdate Tru64 Convert formatted string into time/date structure
getdate_r Tru64 Convert formatted string into time/date structure
pxfestrget IRIX Accesses a single string element of a structure component that is an array
setresult IRIX manipulate Tcl result string
Copyright © 2004-2005 DeniX Solutions SRL
newsletter delivery service