*nix Documentation Project
·  Home
 +   man pages
·  Linux HOWTOs
·  FreeBSD Tips
·  *niX Forums

  man pages->FreeBSD man pages -> sppp (4)              



NAME    [Toc]    [Back]

     sppp -- point to point protocol network layer for synchronous lines

SYNOPSIS    [Toc]    [Back]

     device sppp

DESCRIPTION    [Toc]    [Back]

     The sppp network layer implements the state machine and the Link Control
     Protocol (LCP) of the point to point protocol (PPP) as described in RFC
     1661.  Note that this layer does not provide network interfaces of its
     own, it is rather intended to be layered on top of drivers providing a
     synchronous point-to-point connection that wish to run a PPP stack over
     it.  The corresponding network interfaces have to be provided by these
     hardware drivers.

     The sppp layer provides three basic modes of operation.  The default
     mode, with no special flags to be set, is to create the PPP connection
     (administrative Open event to the LCP layer) as soon as the interface is
     taken up with the ifconfig(8) command.  Taking the interface down again
     will terminate the LCP layer and thus all other layers on top.  The link
     will also terminate itself as soon as no Network Control Protocol (NCP)
     is open anymore, indicating that the lower layers are no longer needed.

     Setting the link-level flag link0 with ifconfig(8) will cause the respective
 network interface to go into passive mode.  This means, the administrative
 Open event to the LCP layer will be delayed until after the lower
     layers signals an Up event (rise of ``carrier'').	This can be used by
     lower layers to support a dialin connection where the physical layer
     isn't available immediately at startup, but only after some external
     event arrives.  Receipt of a Down event from the lower layer will not
     take the interface completely down in this case.

     Finally, setting the flag link1 will cause the interface to operate in
     dial-on-demand mode.  This is also only useful if the lower layer supports
 the notion of a carrier (like with an ISDN line).  Upon configuring
     the respective interface, it will delay the administrative Open event to
     the LCP layer until either an outbound network packet arrives, or until
     the lower layer signals an Up event, indicating an inbound connection.
     As with passive mode, receipt of a Down event (loss of carrier) will not
     automatically take the interface down, thus it remains available for further

     The sppp layer supports the debug interface flag that can be set with
     ifconfig(8).  If this flag is set, the various control protocol packets
     being exchanged as well as the option negotiation between both ends of
     the link will be logged at level LOG_DEBUG.  This can be helpful to examine
 configuration problems during the first attempts to set up a new configuration.
  Without this flag being set, only the major phase transitions
 will be logged at level LOG_INFO.

     It is possible to leave the local interface IP address open for negotiation
 by setting it to  This requires that the remote peer can
     correctly supply a value for it based on the identity of the caller, or
     on the remote address supplied by this side.  Due to the way the IPCP
     option negotiation works, this address is being supplied late during the
     negotiation, which might cause the remote peer to make wrong assumptions.

     In a similar spirit the remote address can be set to the magical value
     0.0.0.* which means that we don't care what address the remote side will
     use, as long as it is not  This is useful if your ISP has several
 dial-in servers.  You can of course route add something_or_other
     0.0.0.* and it will do exactly what you would want it to.

     The PAP and CHAP authentication protocols as described in RFC 1334, and
     RFC 1994 resp., are also implemented.  Their parameters are being controlled
 by the spppcontrol(8) utility.

     VJ header compression is implemented, and enabled by default.  It can be
     disabled using spppcontrol(8).

DIAGNOSTICS    [Toc]    [Back]

     <ifname><ifnum>: <proto> illegal <event> in state <statename>  An event
     happened that should not happen for the current state the respective control
 protocol is in.  See RFC 1661 for a description of the state automaton.

     <ifname><ifnum>: loopback	The state automaton detected a line loopback
     (that is, it was talking with itself).  The interface will be temporarily

     <ifname><ifnum>: up  The LCP layer is running again, after a line loopback
 had previously been detected.

     <ifname><ifnum>: down  The keepalive facility detected the line being
     unresponsive.  Keepalive must be explicitly requested by the lower layers
     in order to take place.

SEE ALSO    [Toc]    [Back]

     inet(4), intro(4), ppp(4), ifconfig(8), spppcontrol(8)

     W. Simpson, Editor, The Point-to-Point Protocol (PPP), RFC 1661.

     G. McGregor, The PPP Internet Protocol Control Protocol (IPCP), RFC 1332.

     B. Lloyd and W. Simpson, PPP Authentication Protocols, RFC 1334.

     W. Simpson, PPP Challenge Handshake Authentication Protocol (CHAP), RFC

AUTHORS    [Toc]    [Back]

     The original implementation of sppp was written in 1994 at Cronyx Ltd.,
     Moscow by Serge Vakulenko <vak@cronyx.ru>.  Jorg Wunsch
     <joerg_wunsch@uriah.heep.sax.de> rewrote a large part in 1997 in order to
     fully implement the state machine as described in RFC 1661, so it could
     also be used for dialup lines.  He also wrote this man page.  Serge later
     on wrote a basic implementation for PAP and CHAP, which served as the
     base for the current implementation, done again by Jorg Wunsch.

BUGS    [Toc]    [Back]


     Currently, only the IPCP control protocol and ip(4) network protocol is
     supported.  More NCPs should be implemented, as well as other control
     protocols for authentication and link quality reporting.

     Negotiation loop avoidance is not fully implemented.  If the negotiation
     doesn't converge, this can cause an endless loop.

     The various parameters that should be adjustable per RFC 1661 are currently
 hard-coded into the kernel, and should be made accessible through

     Passive mode has not been tested extensively.

     Link-level compression protocols should be supported.

FreeBSD 5.2.1		       December 30, 2001		 FreeBSD 5.2.1
[ Back ]
 Similar pages
Name OS Title
ppp FreeBSD point to point protocol network interface
ppp OpenBSD point to point protocol network interface
if_ppp FreeBSD point to point protocol network interface
pppoerd.conf HP-UX PPPoE (Point to Point Protocol over Ethernet) relay configuration file
pppoec.conf HP-UX PPPoE (Point to Point Protocol over Ethernet) client configuration file
pppoesd.conf HP-UX PPPoE (Point to Point Protocol over Ethernet) server configuration file
pppoesd HP-UX PPPoE (Point-to-Point Protocol over Ethernet) server daemon
pppoec HP-UX PPPoE (Point to Point Protocol over Ethernet) client
pppoerd HP-UX PPPoE (Point to Point Protocol over Ethernet) relay
pppstats Tru64 Print Point-to-Point Protocol (PPP) statistics
Copyright © 2004-2005 DeniX Solutions SRL
newsletter delivery service