*nix Documentation Project
·  Home
 +   man pages
·  Linux HOWTOs
·  FreeBSD Tips
·  *niX Forums

  man pages->OpenBSD man pages              
 cua(4) -- general terminal interface
    This section describes the interface to the terminal drivers in the system. Terminal Special Files    [Toc]    [Back] Each hardware terminal port on the system usually has a terminal special device fi...
 cue(4) -- CATC USB-EL1201A USB Ethernet driver
    The cue driver provides support for USB Ethernet adapters based on the Computer Access Technology Corporation's USB-EL1202A chipset. This includes the following adapters: Belkin F5U111 CATC Netmate C...
 cy(4) -- Cyclades Cyclom-{4, 8, 16}Y asynchronous comms board device driver
    This driver provides an interface to Cyclades Cyclom-4Y, Cyclom-8Y and Cyclom-16Y asynchronous multiport serial boards. These boards are based around Cirrus Logic CD1400 communication controllers. The...
 cz(4) -- Cyclades-Z series multi-port serial adapter device driver
    The cz device driver supports the Cyclades-Z series of multi-port serial adapters. The Cyclades-Z is an intelligent serial controller comprising: +o PLX9060ES PCI bus interface +o Xilinx XC5204 FPGA +...
 sparc/daadio(4) -- MATRIX MD-DAADIO digital/analog, analog/digital, parallel i/o board
    The daadio driver provides ioctl(2) entry points to read and write analog/digital, digital/analog, and parallel input/output registers. A typical daadio has 6 8bit parallel ports, 8 12bit DAC ports, a...
 dc(4) -- DEC/Intel 21140, 21142, 21143, 21145 and clones 10/100 Ethernet
    The dc driver provides support for several PCI, MiniPCI, and CardBus Fast Ethernet adapters and embedded controllers based on the following chipsets: +o DEC 21140 PCI +o DEC/Intel 21143 PCI and CardBu...
 hp300/dca(4) -- HP 98644A serial communications interface
    The 98644A is a single port EIA RS-232C (CCITT V.28) communications interface with a single character buffer. Such an interface is built-in to all series 300 machines. Input and output for each line m...
 hp300/dcm(4) -- HP 98642A serial communications multiplexer
    The 98642A is a four port EIA RS-232C (CCITT V.28) communications multiplexer. The 98642A has three direct-connect ports and one port with full modem control. Input and output for each line may be set...
 dcphy(4) -- Pseudo-driver for media support on DEC 21143 controllers
    The dcphy driver handles media selection on the DEC 21143 chip as it has no real MII interface.
 ddb(4) -- kernel debugger
    The ddb debugger provides a means for debugging the kernel, and analysing the kernel after a system crash ("panic"), with a gdb(1)-like syntax. ddb is only available if the kernel was configured wit...
 vax/de(4) -- DEC DEUNA/DELUA 10 Mb/s Ethernet interface
    The de interface provides access to a 10 Mb/s Ethernet network through a Digital Equipment UNIBUS Network Adapter (DEUNA). Each of the host's network addresses is specified at boot time with an SIOCS...
 de(4) -- DEC DC21x4x (Tulip) Ethernet driver
    The de device driver supports Ethernet adapters based on the Digital Equipment DC21x4x based self-contained Ethernet chips. This includes, among others, the following models: Asante Cogent EM100FX and...
 vax/dhu(4) -- DHU-11/DHV-11 communications multiplexer
    A DHU-11 provides 16 communication lines. Normal I/O control parameters for individual lines are managed by ioctl(2) calls. Individual DHU-11 lines may be configured to run at any of 13 speeds (50, 20...
 hppa/dino(4) -- Dino and Cujo Host/PCI bridges
    This driver supports Dino and Cujo Host/PCI bridges found on the A, B, and C models of workstations. Cujo is a 64 bit datapath version of Dino. On some machines it may also provide an additional seria...
 hp300/dio(4) -- DIO/DIO-II bus
    This driver is for the DIO/DIO-II bus on HP 9000/3xx and 9000/4xx series workstations.
<<  [Prev]  1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  
22  23  24  25  26  27  28  29  [Next]  >>
Copyright © 2004-2005 DeniX Solutions SRL
newsletter delivery service