rl -- RealTek 8129/8139 Fast Ethernet device driver
The rl driver provides support for PCI Ethernet adapters and embedded
controllers based on the RealTek 8129 and 8139 Fast Ethernet controller
chips, including the following:
+o Accton ``Cheetah'' EN1207D (MPX 5030/5038; RealTek 8139 clone)
+o Allied Telesyn AT2550
+o Allied Telesyn AT2500TX
+o Belkin F5D5000
+o Compaq HNE-300
+o CompUSA no-name 10/100 PCI Ethernet NIC
+o Corega FEther CB-TXD
+o Corega FEtherII CB-TXD
+o D-Link DFE-530TX+
+o D-Link DFE-538TX (same as 530+?)
+o D-Link DFE-690TXD
+o Edimax EP-4103DL CardBus
+o Encore ENL832-TX 10/100 M PCI
+o Farallon NetLINE 10/100 PCI
+o Genius GF100TXR,
+o GigaFast Ethernet EE100-AXP
+o KTX-9130TX 10/100 Fast Ethernet
+o LevelOne FPC-0106TX
+o Longshine LCS-8038TX-R
+o NDC Communications NE100TX-E
+o Netronix Inc. EA-1210 NetEther 10/100
+o Nortel Networks 10/100BaseTX
+o OvisLink LEF-8129TX
+o OvisLink LEF-8139TX
+o Peppercon AG ROL-F
+o Planex FNW-3800-TX
+o SMC EZ Card 10/100 PCI 1211-TX
+o SOHO(PRAGMATIC) UE-1211C
The RealTek 8129/8139 series controllers use bus master DMA but do not
use a descriptor-based data transfer mechanism. The receiver uses a single
fixed size ring buffer from which packets must be copied into mbufs.
For transmission, there are only four outbound packet address registers
which require all outgoing packets to be stored as contiguous buffers.
Furthermore, outbound packet buffers must be longword aligned or else
transmission will fail.
The 8129 differs from the 8139 in that the 8139 has an internal PHY which
is controlled through special direct access registers whereas the 8129
uses an external PHY via an MII bus. The 8139 supports both 10 and
100Mbps speeds in either full or half duplex. The 8129 can support the
same speeds and modes given an appropriate PHY chip.
Note: support for the 8139C+ chip is provided by the re(4) driver.
The rl driver supports the following media types:
autoselect Enable autoselection of the media type and options.
This is only supported if the PHY chip attached to
the RealTek controller supports NWAY autonegotiation.
The user can manually override the autoselected
mode by adding media options to the
10baseT/UTP Set 10Mbps operation. The mediaopt option can also
be used to select either full-duplex or half-duplex
100baseTX Set 100Mbps (Fast Ethernet) operation. The
mediaopt option can also be used to select either
full-duplex or half-duplex modes.
The rl driver supports the following media options:
full-duplex Force full duplex operation
half-duplex Force half duplex operation.
Note that the 100baseTX media type is only available if supported by the
adapter. For more information on configuring this device, see
rl%d: couldn't map memory A fatal initialization error has occurred.
rl%d: couldn't map interrupt A fatal initialization error has occurred.
rl%d: watchdog timeout The device has stopped responding to the network,
or there is a problem with the network connection (cable).
rl%d: no memory for rx list The driver failed to allocate an mbuf for
the receiver ring.
rl%d: no memory for tx list The driver failed to allocate an mbuf for
the transmitter ring when allocating a pad buffer or collapsing an mbuf
chain into a cluster.
rl%d: chip is in D3 power state -- setting to D0 This message applies
only to adapters which support power management. Some operating systems
place the controller in low power mode when shutting down, and some PCI
BIOSes fail to bring the chip out of this state before configuring it.
The controller loses all of its PCI configuration in the D3 state, so if
the BIOS does not set it back to full power mode in time, it won't be
able to configure it correctly. The driver tries to detect this condition
and bring the adapter back to the D0 (full power) state, but this
may not be enough to return the driver to a fully operational condition.
If you see this message at boot time and the driver fails to attach the
device as a network interface, you will have to perform second warm boot
to have the device properly configured.
Note that this condition only occurs when warm booting from another operating
system. If you power down your system prior to booting FreeBSD,
the card should be configured correctly.
arp(4), miibus(4), netintro(4), ng_ether(4), ifconfig(8)
The RealTek 8129, 8139 and 8139C+ datasheets, http://www.realtek.com.tw.
The rl device driver first appeared in FreeBSD 3.0.
The rl driver was written by Bill Paul <firstname.lastname@example.org>.
Since outbound packets must be longword aligned, the transmit routine has
to copy an unaligned packet into an mbuf cluster buffer before transmission.
The driver abuses the fact that the cluster buffer pool is allocated
at system startup time in a contiguous region starting at a page
boundary. Since cluster buffers are 2048 bytes, they are longword
aligned by definition. The driver probably should not be depending on
The RealTek data sheets are of especially poor quality, and there is a
lot of information missing particularly concerning the receiver operation.
One particularly important fact that the data sheets fail to mention
relates to the way in which the chip fills in the receive buffer.
When an interrupt is posted to signal that a frame has been received, it
is possible that another frame might be in the process of being copied
into the receive buffer while the driver is busy handling the first one.
If the driver manages to finish processing the first frame before the
chip is done DMAing the rest of the next frame, the driver may attempt to
process the next frame in the buffer before the chip has had a chance to
finish DMAing all of it.
The driver can check for an incomplete frame by inspecting the frame
length in the header preceding the actual packet data: an incomplete
frame will have the magic length of 0xFFF0. When the driver encounters
this value, it knows that it has finished processing all currently available
packets. Neither this magic value nor its significance are documented
anywhere in the RealTek data sheets.
FreeBSD 5.2.1 November 4, 1998 FreeBSD 5.2.1 [ Back ]