ata, ar, acd, ad, afd, ast -- generic ATA/ATAPI disk controller driver
For ISA based ATA/ATAPI support:
For PC98 based ATA/ATAPI support:
For PCI based ATA/ATAPI support:
To support ATA compliant disk drives:
To support ATA software RAID's:
To support ATAPI CDROM, DVD and CD/DVD burner drives:
To support ATAPI floppy drives:
To support ATAPI tape drives:
The following tunables are settable from the loader:
set to 1 for DMA access, 0 for PIO (default is DMA).
set to 1 for DMA access, 0 for PIO (default is PIO).
set to 1 to enable Write Caching, 0 to disable (default is enabled).
WARNING: can cause data loss on power failures.
The ata driver provides access to ATA (IDE) and SerialATA disk drives,
ATAPI CDROM/DVD drives, ZIP/LS120 ATAPI drives and ATAPI tape drives connected
to controllers according to the ATA/ATAPI standards.
The currently supported ATA/SATA controller chips are:
Acard: ATP850P, ATP860A, ATP860R, ATP865A, ATP865R
ALI: Aladdin (ALi5229) compatible chips.
AMD: AMD756, AMD766, AMD768, AMD8111.
CMD: CMD646, CMD648, CMD649.
Cypress: Cypress 82C693.
Cyrix: Cyrix 5530.
HighPoint: HPT302, HPT366, HPT366, HPT368, HPT370, HPT371, HPT372,
Intel: PIIX, PIIX3, PIIX4, ICH, ICH0, ICH2, ICH3, ICH4, ICH5.
nVidia: nForce, nForce2, nForce3.
Promise: PDC20246, PDC20262, PDC20263, PDC20265, PDC20267,
PDC20268, PDC20269, PDC20270, PDC20271, PDC20275,
PDC20276, PDC20277, PDC20318, PDC20319, PDC20371,
PDC20375, PDC20376, PDC20377, PDC20378, PDC20379,
PDC20617, PDC20618, PDC20619, PDC20620.
ServerWorks: ROSB4, CSB5, CSB6.
Silicon Image: SiI0680, SiI3112, SiI3114.
SiS: SIS5513, SIS530, SIS540, SIS550, SIS620, SIS630, SIS630S,
SIS633, SIS635, SIS730, SIS733, SIS735, SIS745, SIS961,
SIS962, SIS963, SIS964
VIA: VT82C586, VT82C586B, VT82C596, VT82C596B, VT82C686,
VT82C686A, VT82C686B, VT8231, VT8233, VT8233A, VT8233C,
Unknown ATA chipsets are supported in PIO modes, and if the standard busmaster
DMA registers are present and contain valid setup, DMA is also
enabled, although the max mode is limitted to UDMA33, as it is not known
what the chipset can do and how to program it.
The ata driver can change the transfer mode and various other parameters
when the system is up and running. See atacontrol(8).
The driver sets the maximum transfer mode supported by the hardware as
default. However the ata driver sometimes warns: ``DMA limited to
UDMA33, non-ATA66 cable or device''. This means that the ata driver has
detected that the required 80 conductor cable is not present or could not
be detected properly, or that one of the devices on the channel only
accepts up to UDMA2/ATA33.
ATAPI devices are set to PIO mode by default because severe DMA problems
are common even if the device capabilities indicate support. You can
always try to set DMA mode on an ATAPI device using atacontrol(8), but be
aware that your hardware might not support it and can potentially hang
the entire system causing data loss.
/dev/ad* ATA disk device nodes
/dev/ar* ATA RAID device nodes
/dev/acd* ATAPI CD-ROM device nodes
/dev/afd* ATAPI floppy drive device nodes
/dev/ast* ATAPI tape drive device nodes
/sys/i386/conf/GENERIC sample generic kernel config file for ata based
Please remember that in order to use UDMA4/ATA66 and above modes you must
use 80 conductor cables. Please assure that ribbon cables are no longer
than 45cm. In case of rounded ATA cables, the length depends on the
quality of the cables. SATA cables can be up to 1m long according to the
Static device numbering (enabled with the ATA_STATIC_ID kernel option)
reserves a number for each possibly connected disk, even when not
present. This is useful in hotswap senarios where disks should always
show up as the same numbered device, and not depend on attach order.
The ata driver first appeared in FreeBSD 4.0.
Soren Schmidt <sos@FreeBSD.org>.
FreeBSD 5.2.1 November 4, 2003 FreeBSD 5.2.1 [ Back ]