cp -- copy files
cp [-R [-H | -L | -P]] [-f | -i | -n] [-pv] source_file target_file
cp [-R [-H | -L | -P]] [-f | -i | -n] [-pv] source_file ...
In the first synopsis form, the cp utility copies the contents of the
source_file to the target_file. In the second synopsis form, the contents
of each named source_file is copied to the destination
target_directory. The names of the files themselves are not changed. If
cp detects an attempt to copy a file to itself, the copy will fail.
The following options are available:
-H If the -R option is specified, symbolic links on the command line
are followed. (Symbolic links encountered in the tree traversal
are not followed.)
-L If the -R option is specified, all symbolic links are followed.
-P If the -R option is specified, no symbolic links are followed.
This is the default.
-R If source_file designates a directory, cp copies the directory and
the entire subtree connected at that point. This option also
causes symbolic links to be copied, rather than indirected through,
and for cp to create special files rather than copying them as normal
files. Created directories have the same mode as the corresponding
source directory, unmodified by the process' umask.
Note that cp copies hard linked files as separate files. If you
need to preserve hard links, consider using tar(1), cpio(1), or
-f For each existing destination pathname, remove it and create a new
file, without prompting for confirmation regardless of its permissions.
(The -f option overrides any previous -i or -n options.)
-i Cause cp to write a prompt to the standard error output before
copying a file that would overwrite an existing file. If the
response from the standard input begins with the character `y' or
`Y', the file copy is attempted. (The -i option overrides any previous
-f or -n options.)
-n Do not overwrite an existing file. (The -n option overrides any
previous -f or -i options.)
-p Cause cp to preserve the following attributes of each source file
in the copy: modification time, access time, file flags, file mode,
user ID, and group ID, as allowed by permissions.
If the user ID and group ID cannot be preserved, no error message
is displayed and the exit value is not altered.
If the source file has its set-user-ID bit on and the user ID cannot
be preserved, the set-user-ID bit is not preserved in the
copy's permissions. If the source file has its set-group-ID bit on
and the group ID cannot be preserved, the set-group-ID bit is not
preserved in the copy's permissions. If the source file has both
its set-user-ID and set-group-ID bits on, and either the user ID or
group ID cannot be preserved, neither the set-user-ID nor setgroup-ID
bits are preserved in the copy's permissions.
-v Cause cp to be verbose, showing files as they are copied.
For each destination file that already exists, its contents are overwritten
if permissions allow. Its mode, user ID, and group ID are unchanged
unless the -p option was specified.
In the second synopsis form, target_directory must exist unless there is
only one named source_file which is a directory and the -R flag is specified.
If the destination file does not exist, the mode of the source file is
used as modified by the file mode creation mask (umask, see csh(1)). If
the source file has its set-user-ID bit on, that bit is removed unless
both the source file and the destination file are owned by the same user.
If the source file has its set-group-ID bit on, that bit is removed
unless both the source file and the destination file are in the same
group and the user is a member of that group. If both the set-user-ID
and set-group-ID bits are set, all of the above conditions must be fulfilled
or both bits are removed.
Appropriate permissions are required for file creation or overwriting.
Symbolic links are always followed unless the -R flag is set, in which
case symbolic links are not followed, by default. The -H or -L flags (in
conjunction with the -R flag) cause symbolic links to be followed as
described above. The -H, -L and -P options are ignored unless the -R
option is specified. In addition, these options override each other and
the command's actions are determined by the last one specified.
If cp receives a SIGINFO (see the status argument for stty(1)) signal,
the current input and output file and the percentage complete will be
written to the standard output.
The cp utility exits 0 on success, and >0 if an error occurs.
Historic versions of the cp utility had a -r option. This implementation
supports that option, however, its use is strongly discouraged, as it
does not correctly copy special files, symbolic links or fifo's.
The -v and -n options are non-standard and their use in scripts is not
mv(1), rcp(1), umask(2), fts(3), symlink(7)
The cp command is expected to be IEEE Std 1003.2 (``POSIX.2'') compatible.
A cp command appeared in Version 1 AT&T UNIX.
FreeBSD 5.2.1 July 23, 2002 FreeBSD 5.2.1 [ Back ]